Home  >  PRODUCT  >  Level Instrument  >  Radar Level Meter  > 

Kaidi KDR-908ZT 120 GHz Radar Level Gauge IP68 Gantry frame, locking flange from DN65/ 2.5"

这里可以自定义设置
Kaidi KDR-908ZT 120 GHz Radar Level Gauge IP68 Gantry frame, locking flange from DN65/ 2.5

Kaidi KDR-908ZT 120 GHz Radar Level Gauge IP68 Gantry frame, locking flange from DN65/ 2.5
  • Kaidi KDR-908ZT 120 GHz Radar Level Gauge IP68 Gantry frame, locking flange from DN65/ 2.5
  • 16.jpg
  • 14127.jpg
  • 18.jpg
  • 19.jpg
Kaidi KDR-908ZT 120 GHz Radar Level Gauge IP68 Gantry frame, locking flange from DN65/ 2.5"
B站不支持收货地址
B站不支持库存规格
Application:
rivers,lakes,shallows
Measuring Range:
40 meters
Protection Grade:
IP68
Accuracy:
±2mm
Frequency:
120GHz
Process Pressure:
(-0.1~0.3) MPa
Process Temperature:
-40~80℃
Process Connection:
Gantry frame, locking flange from DN65/ 2.5
MOQ
1 SET
Payments:
TT, Paypal, Credit card, Western union
Shipping ways:
Express(DHL,Fedex,TNT,EMS,UPS)/Air/Sea
参数暂无数据
多属性暂无数据
B站不支持优惠卷

Add success, do you want to check your shopping cart?

暂无分享
B站不支持产品保障
PRODUCT PRINCIPLE

The general principle of the FM continuous wave radar level gauge is that the radar emits electromagnetic waves on the top of the tank, and the electromagnetic waves are received by the radar after being reflected by the medium. The frequency difference δf between the received signal and the transmitted signal is proportional to the distance R from the surface of the medium: R=C (speed)*δf (frequency difference)/2/K (frequency modulation slope). Because the speed of light C and the frequency modulation slope K are known, the frequency difference δf can be estimated to obtain the distance R from the radar installation position to the material surface, and then through the known total height of the tank, subtract the spatial distance from the radar to the material surface (referred to as Empty height) to get the height of the material level. 

PROUCT CHARACTERISTICS

Small beam angle, concentrated energy, stronger anti-interference ability, higher measurement accuracy


Small size and light weight, easy to install


The protection level is up to IP68, which is suitable for a variety of water level measurement occasions.


The measurement range is up to 40 meters, covering large-scale reservoirs and other water level measurement


Multiple output circuit interfaces to cooperate with the acquisition system 


PRODUCT INTRODUCTION

PRODUCT  INSTALLATION

Preparation before installation

 

Please pay attention to the following items to ensure that the meter can be installed correctly:

Please reserve enough space for installation.

Please avoid installation situations with strong vibration.

 

Illustration and installation location 


Note: When a radar antenna emits microwaves, it has a certain emission angle. There should be no obstacles from the lower edge of the antenna to the surface of the measured medium, and in the area radiated by the emitted microwave beam. Therefore, shielding facilities should be avoided as much as possible during installation, and “false echo learning” must be carried out when necessary. Also pay attention when installing the instrument: the highest liquid level must not enter the blind area of the measurement. 


THE ELECTRICAL CONNECTION

Supply voltage

 

Modbus-RS485

Separate the power supply and Modbus signal lines with a shielded cable respectively. For the specific power supply voltage range, please refer to the technical data.     


Safety guidance

Please comply with the requirements of local electrical installation regulations!

Please abide by the local regulations on the health and safety of personnel. All operations on the electrical components of the instrument must be completed by properly trained professionals.

Please check the nameplate of the meter to ensure that the product specifications meet your requirements. Please make sure that the power supply voltage is consistent with the requirements on the nameplate of the meter.

Protection level

This meter fully meets the requirements of protection class IP68, please ensure the waterproofness of the cable sealing head. As shown below:

 

How to ensure that the installation meets the requirements of IP68:

Make sure that the sealing head is not damaged.

Make sure that the cable is not damaged.

Make sure that the cables used meet the requirements of the electrical connection specifications.

Before entering the electrical interface, bend the cable downward to ensure that water does not flow into the housing.

Please tighten the cable gland.

Please block the unused electrical interfaces with blind plugs. 

INSTRUMENT COMMISSIONING

There are two debugging methods for radar water level gauge:           

 

(1)Mobile phone Bluetooth debugging/connecting to the Bluetooth debugging radar through the WeChat applet

(2) Host computer debugging/debugging through MUDBUS protocol

 

Upper computer debugging

Connect to the host computer through the RS485 converter

① RS232 interface/or USB interface

② Radar water level gauge

③ RS485 converter


STRUCTURE SIZE(UNIT:MM)

METER LINERARITY

The launch angle depends on the antenna size

 

-42mm    

Accuracy     see the figure below 


TECHNICAL PARAMETERS

SELECTION PARAMETER TABLE

该产品后台详情无内容

Please Send Us your Application details

Measuring range , medium, Installation method (flange, thread), Pressure range, Remote transmitter, Level alarm switch

Our technical team will check your specifications and make a best solution for you.

社媒暂无评论

More  Model available for all appication, different termperture and pressure!

Chat Online 编辑模式下无法使用
Leave Your Message inputting...