West source technology to guide how to install and use correctly input type liquid level change to send

by:Kaidi Sensors     2021-01-04
XY series into type liquid level transmitter is based on the measured liquid the principle of static pressure is proportional to the height of the liquid, the piezoresistive effect of diffused silicon or ceramic sensitive element, the static pressure into electrical signals. After temperature compensation and the linear correction. Is transformed into 4 - 20 madc standard current signal output. XY series into type liquid level transmitter good stability, high precision, the sensor part can be directly into the liquid, transmitter part available flange or bracket, convenient in installation. Solid state structure, no moving parts, high reliability, long service life from water and oil to high-precision measurements, larger paste viscosity can not be measured medium blister, deposition, the influence of the electrical characteristics of wide range of temperature compensation. Input type liquid level transmitter has a power supply reverse polarity protection and overload current limit protection. Input type liquid level transmitter use and installation of the notice: 1. Liquid level transmitter should be restored the original packing, transportation, storage in a cool, dry and ventilated warehouse. 2. Use found abnormal, should turn off the power and stop using, check 3. Welding power supply connection should be in strict accordance with the wiring instructions. Input type liquid level transmitter to install: level gauge shall be installed in the stillness of the deep well, sink, usually the bore diameter & Phi; About 45 mm steel pipe ( Different height to play several holes, so that the water flow into the tube) Fixed in the water, and then input type liquid level transmitter can be used in the steel pipe. The installation of the transmitter is in the vertical, the inputting type installation position should be far away from the liquid accesses and blender. In the use of larger vibration occasions, but in the transmitter coil wire, using steel wire suspension, so as to avoid tensile cables. Measuring flow or stirring the liquid level, usually the bore diameter & Phi; About 45 mm steel pipe ( Different heights on the opposite side of the liquid flow to play several holes, so that the water flow into the tube) Fixed in the water, and then input type liquid level transmitter can be used in the steel pipe. Humidity sensor probe, PT100 sensor electric heating tube, stainless steel, cast aluminum heater, heating coil fluid solenoid valve about input type liquid level transmitter solution how to solve the problem of anti-interference, input type level gauge good stability, high accuracy, installation is very convenient. In daily use will be affected by many factors. To enable users to better use input type level gauge, the following will be related methods to share with you. First everyone is using the traditional method to solve but not very good effect. For the traditional method is the measuring equipment on a small tank of liquid level, the pressure transmitter detector installed in the bottom of the tank, sex of sensor line is good. But there is a problem, when water tank with water flow down, can make the following pressure oscillation is larger. Analysis data, take out a data in 1 second, the motion of the display is large, which has the correct values; With 10 ms took out a number of average, the effect is not good. How to solve? Avoid liquid low pressure probe directly, or with other objects blocking liquid mean when the moment it is ok to directly impact pressure; At the same time can put water inlet into the shower, put a big water spraying down, cut into small water effect is good. Bend the inlet pipe mouth, slightly upwards water inlet, water when out into the air and then fall first, reduced the direct impact ( Converting kinetic energy into potential energy) 。
Guangdong Kaidi Energy Technology Co., Ltd. is recognized as one of the leading manufacturer of in China.Trust in us and make Guangdong Kaidi Energy Technology Co., Ltd. your level gauge supplier. Our products will bring more economic value to you.
Make your customized level indicator customized level indicator. Invest in professional level gauge services. For more info, check out Kaidi level indicator.
Forging an tight connection starts with understanding your potential customers and catering to their needs on level gauge, both with a quality product and impactful customized level indicator.
Guangdong Kaidi Energy Technology Co., Ltd. quickly recognized the power of efficient manufacturing and started proactively recruiting people to sell products.
Guangdong Kaidi Energy Technology Co., Ltd. provides innovative technology and prompts our customers to know the development of our producing level gauge.
Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...