Home  >  PRODUCT  >  Conveyor Belt Safety Switches  > 

Two-Way Pull Cord Switch With Led KPC-LED

这里可以自定义设置
Two-Way Pull Cord Switch With Led KPC-LED

Two-Way Pull Cord Switch With Led KPC-LED
  • Two-Way Pull Cord Switch With Led KPC-LED
  • 356.jpg
  • led3.jpg
  • led5-1.jpg
  • led4.jpg
Two-Way Pull Cord Switch With Led KPC-LED
B站不支持收货地址
B站不支持库存规格
Process Temperature:
2A2B
Outer Covering:
5-10 days
Process temperature:
1 SET
MOQ
1 SET
Shipping ways:
Express(DHL,Fedex,TNT,EMS,UPS)/Air/Sea
Ambient Temperature:
-25 °C ~ +60°C
Outer Covering:
5A/220VAC
参数暂无数据
多属性暂无数据
B站不支持优惠卷

Add success, do you want to check your shopping cart?

暂无分享
B站不支持产品保障
该产品后台详情无内容
这里可以自定义设置

PRODUCT INTRODUCTION

High-quality stainless steel casting, high strength, never rust, IP67 protection rating, and good sealing. Pull Cord Switch is an emergency switch to stop the belt conveyor instantly when an accident happens. Since the Pull Cord Switch is so designed that it should be installed at the side of belt conveyor and the pull cord should be mounted along conveyor, the switch can be actuated at any position. Weatherproof type: IP67. The internal contact is the high performance micro switch from Japan, with high contact capacity. It can directly control high capacity contactor, with 2 normally open and 2 normally closed output. Additionally, we also produce pull cord switch with the internal contact close to the sensor.

WIRING DIAGRAM & DRAWING

ENVIRONMENTAL CONDITIONS

The belt sway switch should be used in the following environmental conditions; especially made products should be used at the allowable conditions noted in the approved drawing or the final drawing.

● Temperature: -10°C ~ +50°C

Do not use the belt sway switch in the place where there is danger of freezing.

● Humidity less than 80%

● Dust

If much dust adheres to the touch roller and it solidifies the belt sway switch will not move normally. To prevent dust from adhering to the touch roller, it should be cleaned at regular intervals.

● Explosive and Corrosive Environment

The standard Pull Cord Switch should never be use under these conditions.

PRODUCT INSTALLATION

这里可以自定义设置

PRODUCT MAINTENANCE

 

Periodic Inspection

(1) Cleaning

Always clean when an excessive amount of dust accumulates on the touch roller.

(2) Wear of Touch Roller

Check wear of the touch roller . When 2 millimeters are worn off the roller, replace as explained in 6.3.

(3) Confirmation of Action

Check to see if the Belt Sway Switch is working normally by testing the touch roller.

Lubrication

The Belt Sway Switch has no need to lubricate.

Replacement of Touch Roller

By loosening the 12 millimeters-sized nut, the touch roller can be taken off easily from the lever.

Secure the nut when the touch roller is replaced, or the Belt Sway Switch may cause trouble if the nut comes loose.

Tightening of Cover

When taking off the cover of belt sway switch for the sake of writing, adjusting and checking, secure the screws of the cover after working, or the belt sway switch may cause trouble due to water and dust entering from between the cover and casing.

Please Send Us your Application details

Measuring range , medium, Installation method (flange, thread), Pressure range, Remote transmitter, Level alarm switch

Our technical team will check your specifications and make a best solution for you.

社媒暂无评论

More  Model available for all appication, different termperture and pressure!

Chat Online 编辑模式下无法使用
Leave Your Message inputting...