loading
Kaidi Sensors  >  AI - Page Sitemap  >  top level 2 radar manufacturers for detecting
top level 2 radar manufacturers for detecting

top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting
  • top level 2 radar manufacturers for detecting

top level 2 radar manufacturers for detecting

PRODUCT...
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:


PRODUCT OVERVIEW

This series of radar level meter adopted 26G high frequency radar sensor, the maximum measurement range can reach up to 10 meters. Antenna is optimized further processing, the new fast microprocessors have higher speed and efficiency can be done signal analysis, the instrumentation can be used for reactor, solid silo and very complex measurement environment.


top level 2 radar manufacturers for detecting-1


THE PRODUCT PRINCIPLE

Radar level transmitter antenna microwave pulse is narrow, the downward transmission antenna. Microwave exposure to the medium surface is reflected back again by the antenna system receives, sends the signal to the electronic circuit automatically converted into level signals (because the microwave propagation speed, electromagnetic wave to reach the target and the reflected back to the receiver this time is almost instantaneous).


top level 2 radar manufacturers for detecting-2

Datum measurement:  Screw thread bottom or the sealing surface of the flange.

Note: Make sure the radar level meter the highest level cannot enter the measuring blind area (Figure D shown below).


PROTECTION GFEATURES

top level 2 radar manufacturers for detecting-3

Ø Small antenna size, easy to install; Non-contact radar, no wear, no pollution.

Ø Almost no corrosion, bubble effect; almost not affected by water vapor in the atmosphere, the temperature and pressure

changes.

Ø Serious dust environment on the high level meter work has little effect.

Ø A shorter wavelength, the reflection of solid surface inclination is better.

Ø Beam angle is small, the energy is concentrated, can enhance the ability of echo and to avoid interference.

Ø The measuring range is smaller, for a measurement will yield good results.

Ø High signal-to-noise ratio, the level fluctuation state can obtain better performance.

Ø High frequency, measurement of solid and low dielectric constant of the best choice.


PRODUCT SPECIFICATION

top level 2 radar manufacturers for detecting-4



APPEARANCE OF SIZE

top level 2 radar manufacturers for detecting-5


TECHNICAL PARAMETERS

top level 2 radar manufacturers for detecting-6top level 2 radar manufacturers for detecting-7

top level 2 radar manufacturers for detecting-8top level 2 radar manufacturers for detecting-9top level 2 radar manufacturers for detecting-10

INSTALLATION REQUIREMENTS

top level 2 radar manufacturers for detecting-11

top level 2 radar manufacturers for detecting-12

top level 2 radar manufacturers for detecting-13

top level 2 radar manufacturers for detecting-14



Kaidi Sensors level 2 radar is produced combining the decoration technique with manual finishing drawing. When the product is fired, the drawing will stick to the glaze tightly, and hence to create different patterns. This product has the ability to accurately convert a physical parameter into a signal
Any raw materials used in Kaidi Sensors level 2 radar will be tested before production, including hardness, density, and water resistance tests. All these tests must be conducted in line with the shoe materials requirements. This product can be used in many different industries such as food & beverage, water, energy, pharmaceutical, etc
Before production, the electrode materials of Kaidi Sensors level 2 radar are carefully handled to prevent them from coming into contact with each other. Because contamination between the anode and cathode materials will ruin the battery. This product is notable for its strong overload capacity
The production process of Kaidi Sensors level 2 radar is well-controlled. From the extraction of raw materials to the mixture, forming, and cutting, every step is highly efficient. It is suitable for extreme pressure conditions
The inspection of Kaidi Sensors level 2 radar is strictly conducted. It has passed the inspection of the spectrometer with reasonable light color temperature. This product is mainly used for the automation process
The product is in the best quality at competitive, affordable prices. Since it is maintenance-free, this product significantly helps save operation costs
Product Message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...