How to select the turbine flowmeter

How to select the turbine flowmeter is a question that customers often consult. After all, the turbine flowmeter is a kind of industrial instrument and meter, and many parameters need to be confirmed before buying, so that the flowmeter suitable for industrial site can be selected. At present, there are many turbine flowmeter manufacturers on the market, and the on-site selection capabilities of each manufacturer are also different. It is very important to choose an engineer with rich experience to help with the selection. The following editor will list the main parameters to be confirmed in the selection to facilitate everyone's purchase.　　Not much to say, the selection of turbine flowmeter, the parameters that need to be confirmed mainly include the following points: 　　1, measuring medium. Turbine flowmeter is a velocity flowmeter, which first converts the flow rate of the medium to the rotational speed of the turbine, and then converts the rotational speed into an electrical signal proportional to the flow. Its principle determines the type of its measuring medium, which can only be gas, or liquid without fiber or particle impurities such as water, pure water, organic liquid, and inorganic liquid. Because fibers, particles, impurities, etc. may entangle the blades of the turbine, or cause losses to them, the measurement accuracy may be affected, and the rotation may even stop.　　2, pipe diameter. Unlike other flow meters, the diameter of turbine flow meters can be very small, theoretically DN4, while other flow meters generally can only be DN15 or more. However, the upper limit of the diameter of the turbine flowmeter is also very small. In theory, it can only be DN200, and it can also meet most of the needs of the market. Turbine is mostly used in some high-precision applications, such as quantitative control, a lot of turbine flowmeters will be used.　　 3. Measurement accuracy. The accuracy of the turbine flowmeter also has several levels, the conventional ones are 0.5 and 1.0. These two levels can basically meet the needs of most industrial sites. However, in some occasions with higher accuracy requirements, higher grades are often required. Don't worry, other flowmeters can rarely reach it, but our turbine flowmeter can achieve 0.2 grade accuracy. Is it very powerful? 　　4. Medium viscosity. The principle of the turbine flowmeter was mentioned earlier. The turbine flowmeter uses the flow rate of the medium to convert the speed of the turbine, and then converts the speed into an electrical signal proportional to the flow. The principle determines that the turbine flowmeter is not suitable for measuring too viscous liquid, otherwise it will affect the rotation of the impeller (in this case, it is more suitable to use an oval gear flowmeter). Theoretically speaking, the medium viscosity of the turbine flowmeter should be less than 5×10-6m2/s (for liquids larger than 5×10-6m2/s, the flowmeter should be calibrated for the actual liquid before use). In layman's terms, the viscosity should be less than The cooking oil is small.　　 5. Nominal pressure. According to the current market demand, there are mainly 1.0Mpa; 1.6Mpa; 2.5Mpa; 4.0Mpa; 6.3Mpa (other pressure levels can be customized and supplied according to agreement).　　 6. Medium temperature. According to the current market demand, the main temperature range is -20℃～+120℃ (stainless steel measuring tube). If you need a larger range, you can consult the manufacturer to see if it can be customized.　　7, power supply. According to the current market demand, there are mainly 3.6V lithium battery; 12VDC; 24VDC three power supply methods are optional. You can choose the power supply method that suits you according to the on-site working conditions.　　 8. Output signal. According to the current market demand, there are mainly three-wire pulse output and two-wire 4-20mA output. In addition, some occasions may require digital output, we can also provide modbus RS485 communication and RS232 communication.　　 Generally speaking, the above 8 points basically contain all the important parameters required for turbine flowmeter selection. Once these points are confirmed, the manufacturer can recommend a suitable model for you, and the price will come out. So, when you get a purchase request, don’t rush to find the manufacturer to make an inquiry. As the saying goes, sharpening the knife does not cut wood by mistake. After confirming the above-mentioned parameters, you can save a lot of time when inquiring with the manufacturer. , Get a quote quickly.
As we have known for quite some time, the success of KAIDI in the future will depend greatly on our ability to strike a balance between valuable human insight and interaction with technology.
Excellent quality yet affordable best at Kaidi level indicator. Don't miss out!
Undoubtedly, level gauge are made with advanced equipment.